Concrete cutting in Clermont FL - a clean, straight cut right where you need it
Need a door through a concrete wall or a pipe through a slab? We scan it first, then cut it clean and straight.
How do you cut an opening in existing concrete in Clermont?
Concrete cutting in Clermont means sawing or drilling through a slab or wall that's already there, so a door opening, a pipe hole or a section of driveway comes out along a clean, straight line instead of a jagged break.
Usually you're here because something has to change in concrete that's already poured. Maybe a garage is becoming a room and needs a door through the wall, a new bathroom needs a drain run through the slab, or a cracked panel of driveway has to come out without wrecking the rest. The price moves with how many feet we cut, how thick the concrete is, how much steel is in it and whether it's a floor, a wall or a set of round holes. The schedule usually turns on the scan and on whether the work needs a permit more than on the sawing itself, and your own figure comes from the estimate I leave you.
How we handle concrete cutting, from the scan to the cleanup
Before we pick a cut line, we have the slab or wall scanned so we know what's inside it, because a line moved a few inches on paper beats finding a cable with the blade. Then we match the tool to the cut. Floors, driveways and sidewalks get a walk-behind saw with a big diamond blade, which is the everyday way to cut flat concrete. A door or window opening in a wall gets a track saw that rides a rail bolted to the wall, because the rail holds the blade straight where a handheld saw would wander. Round holes for pipes, drains and conduit get a core drill, a hollow bit that pulls out a clean plug, so we aren't sawing a square hole and patching it. Once the cut's done, we break out the piece, haul it off and clean up.
Cutting is often the first half of a bigger job. When you're widening a driveway or replacing a sunken panel, we saw a straight edge on the old slab so a new concrete driveway meets it cleanly, and we do the same before concrete patio construction adds onto a back slab.
Concrete cutting and permits at Clermont houses
The City of Clermont requires a city permit to alter or demolish a structure, and its list of work that needs no permit names things like painting, flooring, tile and fixtures, not concrete cutting. That list doesn't settle it for a cut, and a door through a wall changes the structure, so we check your job with the city before we start.
A lot of the houses we cut into around Clermont sit on a slab with block walls, so the same calls come up again and again: a garage turned into a bedroom, a slider cut into a back wall, a drain line run through the floor for a new bath. A slab can carry steel or conduit nobody marked when it was poured, which is why the scan comes first even on a job that looks simple. The tricky ones, like an opening in a wall you can barely reach, are honestly the jobs I like most. We see the same kinds of houses on jobs in Minneola and Winter Garden, and we work in the cities around Clermont across Lake and Orange counties and beyond, so ask even if yours isn't listed.
How concrete cutting works
Call or send the form
Reach us at (352) 995-0299 or through the form. We'll set a day to meet at the house and look at the spot together.
I look and write it up
I come out, measure, check how close we can get a saw and ask a lot of questions about what's behind or under the concrete. Your estimate spells out the method, the scan and each pipe hole as its own line, so you can see what drives the number.
We scan and handle permits
We have the slab or wall scanned and take care of any permit the job needs before a blade comes out. If the work includes digging or demolition, Florida law requires notice to the state's underground utility system at least 2 full business days ahead, so we build those days into your start date.
We cut and walk it together
We make the cut, break out the piece and clean up the work area. Then we walk it with you, look at the edges together and go over what comes next if new concrete is going in.
Get a free estimate for your concrete cut and the slab work after it
Send the form and we'll get back to you within 1 business day to set a time. I come out, look at the wall or slab, ask my questions and leave you a free estimate on site. There's no pressure and no obligation.
Common questions about concrete cutting
How much does concrete cutting cost in Clermont?
Professional concrete saw cutting across the US usually costs about $4 to $15 per linear foot, and that covers the saw cut itself, while pipe holes are priced separately. Reinforced or thicker slabs cost more per foot than an ordinary 4 to 6 inch slab, and on a small job a minimum or setup charge can make up most of the price. Your own number comes from the estimate.
What does a scan show before you cut concrete?
A ground penetrating radar scan, GPR for short, shows what's inside a slab or wall before anyone picks a cut line, by sending pulses into the concrete and reading what bounces back. It picks up rebar, the steel bars that strengthen concrete, post-tension cables, which are steel cables pulled tight inside some slabs, plus conduit and hollow spots.
Why is concrete cut with water?
Most concrete sawing runs wet because water cools the diamond blade, keeps the dust down and makes the blade last longer. The water mixes with the cuttings into a gray slurry, and we vacuum or contain it as we go so it isn't left running across your yard or driveway.
Can you cut concrete inside a house or garage in Clermont?
Yes, and the choice of saw matters more indoors. The sawing trade group's guidance says whoever runs the job has to provide good ventilation when an engine-powered saw cuts inside, and it lists electric, hydraulic and air-powered saws as other options, so tell us when the cut's indoors and we'll plan around it.
What causes a slab to crack when part of it is cut out?
Usually it's breaking the concrete out without sawing a line first, because a hammered break follows the weakest path through the slab instead of the line you wanted. A full-depth saw cut gives the piece a clean edge to separate along, and if old cracks already run into the area, I'll point them out at the estimate.
How do I get my house ready for concrete cutting?
Clear the area around the cut, move cars off the driveway and tell us about any lines you already know run through the wall or floor. Inside, move furniture away from the spot and keep kids and pets out of the room, since wet sawing throws water and slurry.
Why Clermont homeowners call Clermont Concrete Company to cut concrete
I'm on site for the cut
Our own crew does the cutting with me there, not a crew working off someone else's notes. If something unexpected shows up in the wall, the person who planned the job is right there to decide what to do.
Trained by a demanding boss
We started here in 2023, after I spent years on crews for a boss who made us tear out anything that wasn't right. That's why the parts you don't see, like the scan, the layout and the setup, get as much care as the cut itself.
Licensed, insured, permits handled
We're licensed and fully insured, and the city lets any current state-licensed contractor pull a building permit in Clermont. When your cut needs a permit, we pull it and handle the inspections with the office that covers your address.
On any cut, what matters most is knowing what's in the concrete before the blade goes in. Tell us about your job and I'll come take a look.
Work that often follows a cut
Concrete driveway building
When the old driveway is past saving, a full new slab on a dug-out, packed base can follow the cut instead of patching around it.
Concrete patio construction
If the back slab is cracked or pitched toward the house, we can cut out the bad part and pour a patio that drains the right way.
Tell us about your wall or slab cut
Call (352) 995-0299 or use the form with where the cut is, how big it is, what it's for and whether it's indoors, so I come out with the right saw already in mind.
